VendorsExamsEnterprise
Support
Request an ExamContact UsFAQ
Dell

Dell VxRail Deploy (D-VXR-DY-02) Free Sample Questions

Create a free account to browse all 12 sample questions. The full practice test includes 150 questions. Use the simulator for timed and flashcard mode.

Try Simulator

D-VXR-DY-02 Sample Questions

  1. Q1

    An implementation engineer is preparing a Top-of-Rack (ToR) switch for a new VxRail deployment. To ensure that the VxRail Manager can automatically discover the unconfigured nodes via the Loudmouth protocol, which specific networking feature must be enabled on the management VLAN?

    Show answer & explanation

    Correct answer: B

    VxRail uses the Loudmouth protocol for node discovery, which relies on IPv6 multicast. Therefore, IPv6 multicast traffic must be allowed on the native VLAN (or the designated management VLAN) connecting the VxRail nodes. MLD snooping or an MLD querier is often configured to manage this traffic.

    Timed and flashcard mode in the Simulator
  2. Q2

    A customer requires their new VxRail cluster to be deployed using an existing, customer-managed vCenter Server. The implementation specialist is validating the prerequisites on the external vCenter.

    Which logical object must already exist in the customer-managed vCenter before initiating the VxRail first-run deployment?

    Show answer & explanation

    Correct answer: C

    When deploying VxRail with a customer-managed (external) vCenter, a Datacenter object must exist prior to deployment. The VxRail deployment wizard will create the cluster object (or it can be pre-created, but the datacenter must exist) and the VDS during the installation process.

    Timed and flashcard mode in the Simulator
  3. Q3

    A global enterprise is planning a Layer 3 (L3) VxRail deployment across multiple racks. The architect has mapped out the subnets for Management, vSAN, and vMotion.

    Reviewing the architecture, what is a mandatory requirement regarding the VxRail Manager and vCenter Server IP addressing in this topology?

    graph TD subgraph Rack 1 Node1[VxRail Node 1] Node2[VxRail Node 2] Node3[VxRail Node 3] end subgraph Rack 2 Node4[VxRail Node 4] Node5[VxRail Node 5] end Router[L3 Router] Node1 & Node2 & Node3 --> Router Node4 & Node5 --> Router
    Show answer & explanation

    Correct answer: B

    Even in a Layer 3 VxRail cluster deployment where ESXi management, vMotion, and vSAN networks can be routed across racks, the VxRail Manager VM and the vCenter Server VM (if internal) must reside in the same subnet/VLAN to maintain proper management connectivity and function.

    Timed and flashcard mode in the Simulator
  4. Q4

    True or False: When preparing DNS for a new VxRail deployment, both Forward (A) and Reverse (PTR) records are strictly required for the ESXi hosts, VxRail Manager, and vCenter Server.

    Show answer & explanation

    Correct answer: A

    True. VxRail pre-installation validation strictly checks for the presence of both Forward (A) and Reverse (PTR) DNS records for all primary infrastructure components (ESXi hosts, vCenter, VxRail Manager). If any are missing, the validation will fail.

    Timed and flashcard mode in the Simulator
  5. Q5Multiple answers

    During the pre-deployment phase, an engineer is filling out the configuration parameters. Which TWO pieces of information must be provided specifically for the vSAN network? (Select TWO)

    Show answer & explanation

    Correct answers: A, B

    The vSAN network requires a starting IP address (which will be incremented for each node) and a VLAN ID to segregate the storage traffic. Hostnames are not assigned to vSAN interfaces, and a Default Gateway is typically only required if routing vSAN traffic (L3), but starting IP and VLAN ID are always required.

    Timed and flashcard mode in the Simulator
  6. Q6

    A deployment engineer runs the pre-install validation tool on a VxRail Manager before starting the build. The tool reports an error regarding MTU mismatch.

    What is the most common cause of this specific validation failure?

    Show answer & explanation

    Correct answer: B

    An MTU mismatch during pre-install validation almost always occurs because the deployment configuration specifies Jumbo Frames (MTU 9000) for vSAN and/or vMotion, but the upstream Top-of-Rack (ToR) switch ports have not been configured to allow frames larger than the default 1500 bytes.

    Timed and flashcard mode in the Simulator

Register free to unlock 6 more sample questions

Create a free account to continue with the rest of the D-VXR-DY-02 sample set.

Lifetime One

Own this practice test forever.

$79.99
$75.99
one-time
  • Full access to 150 questions
  • Study, Timed & Flashcard Modes
  • All past and future versions i
  • Detailed Explanations
  • Study Tracking & Past Attempts
  • Brainy AI Assistant
  • Lifetime updates

Two

Any 2 exams per month.

$20.00/exam
$39.99
/month
  • 2 active exam slots
  • Study, Timed & Flashcard Modes
  • All past and future versions i
  • Detailed Explanations
  • Study Tracking & Past Attempts
  • 1,000 Brainy AI Credits
  • Cancel anytime
Popular

Pro Four

Any 4 exams per month.

$17.50/exam
$69.99
/month
  • 4 active exam slots
  • Study, Timed & Flashcard Modes
  • All past and future versions i
  • Detailed Explanations
  • Study Tracking & Past Attempts
  • 5,000 Brainy AI Credits
  • Dedicated support

Premium Twelve

Any 12 exams over 3 months.

$15.00/exam
$179.99
/3 months
  • 4 active exam slots
  • Study, Timed & Flashcard Modes
  • All past and future versions i
  • Detailed Explanations
  • Study Tracking & Past Attempts
  • 15,000 Brainy AI Credits
  • Dedicated support
  • Friend seat included — full access

Trusted by professionals at

NvidiaSupabaseGitHubOpenAITursoClerkClaude AIAmazon